Anti static PVC tile is a conductive mesh structure in PVC floor. PVC is not conductive in the mesh. This is the soft rib and defect of tile.

In order to make up for this defect, the inventor or original designer of anti static PVC tile specially designed the anti-static floor wax, that is, after laying anti static PVC tile, put anti-static floor wax, so that the whole floor gets a uniform anti-static function. However, after this technology was introduced to China, it gradually changed its appearance. Many users did not play anti-static floor wax in order to save costs, because the test results were ok. This is actually not true, and sometimes the test results have their limitations. This is the root cause of anti static PVC tile that must be coated with antistatic floor wax.

The anti-static floor is originally a coating, and its anti-static effect will be damaged by time and friction. Anti-static floor wax generally has an anti-static effect for 30 days, which can enhance the anti-static effect of anti-static floor, and the surface resistance can reach at least 1 megohm.

The antistatic floor wax coating can improve or maintain the static electricity consumption function of the anti static PVC tile. Antistatic floor wax can form a protective wax film on the surface of the anti-static floor. The daily generated ground dirt is isolated on the wax film and will not pollute the floor. In this way, we can significantly extend the service life of expensive anti-static floors and protect our investment.

At the same time, the anti-static floor wax can effectively improve the gloss of the anti static PVC tile, beautify the environment, and improve the anti-slip performance of the anti-static floor.

anti-static PVC flooring

People think that there is anti-static effect after installing anti-static PVC flooring, but it is not. The reason why the floor can be anti-static is because the grounding treatment under the floor, then what is the anti-static PVC flooring grounding method?

Epoxy epoxy grounding

When laying copper nets, leave a wiring head in each corner to connect with the grounding wire. If there are multiple grounding wires in a large area, at least one grounding wire should be set every 100 square meters. The best condition is A grounding system is designed separately to distinguish it from the grounding system of the building.

Straight grounding

When laying the copper mesh, leave a wiring head in each corner to connect with the grounding wire. (Since the copper mesh is thin and easy to break, it is recommended to use a flat copper wire at the grounding end. It is better to bury the copper wire directly under the floor and copper. If the network is connected to a large area, it is necessary to set up at least one grounding wire per 100 square meters. It is best to design a grounding system separately to distinguish it from the grounding system of the building.

Raised floor grounding

(1) Simple grounding treatment: Since the overhead type anti-static floor is entirely conductive, we only need to connect the grounding wire in the room to the bracket below the floor to achieve anti-static effect.
(2) Standard grounding treatment: Before installing the anti-static floor, firstly lay a copper row with a size of 30x3mm on the ground. Only one copper row should be laid on each side. When laying, each copper row should be connected. Then connect with the grounding wire in the room. When installing the anti-static floor support frame, connect the support frame to the copper bar every 2 meters with copper wire. This will make the anti-static effect better.

Anti-static PVC flooring is mainly used in computer room, special ward, precision workshop and other spaces that have special requirements for static electricity. Therefore, anti-static PVC floor is also a kind of PVC floor. However, rubber flooring can also be anti-static by adding some conductive components.

Conductive PVC floor is a permanent conductive body with PVC resin as the main body. It is also homogenous and transparent. The material from the bottom to the surface is the same. If the surface is burnt or scratched, Broken, you can use a sander to grind and re-wax as new. Static electricity in the computer room can slow down the computer until it fails, causing errors in the computer’s operation and causing breakdown and destruction of some computer devices.

Advantages of Conductive PVC Floor

1. There are many types of anti-static flooring: tile anti-static floor, conductive PVC floor, steel anti-static floor. The anti-static floor tile is made of anti-static ceramic tile and is surrounded by conductive rubber strip. It has anti-static, environmental protection, high temperature resistance, long life, waterproof, decorative and other excellent functions, but the tile anti-static The weight of the floor is heavier, the cost is higher, and the disadvantage of inconvenient installation is less used in our lives.

2. The anti-static floor of steel in anti-static floor is made of very wear-resistant hpl fireproof board and pvc as the surface layer. The steel shell is used as the structural base material, and the edges are edgeless and edged. The price of steel anti-static floor is low, the construction is convenient, and there will be no gap after installation. However, the steel anti-static floor has a short life span, and the surface is not wear-resistant. The use range is much smaller than that of the conductive PVC floor.

3. Anti-static floor will use adhesive in the process of installation, and adhesive is one of the main components of formaldehyde. Formaldehyde is regarded as an invisible killer in our lives and is extremely harmful to our health. This makes us pay special attention to the purchase. If you smell a pungent smell, we should never buy it. When buying, we must buy products that have passed the national environmental protection test. conductive PVC floor has relatively good environmental performance.

4. Conductive PVC floor in the installation process we should pay attention to: keep the ground sanitation, do a good protection against shielding, to ensure that the ground is level, the ground fixed line power supply is complete, the floor installation should be stable and firm, the edge of the floor should be maintained Straight line, the gap between the two anti-static floors is not easy to be too large and other precautions. Thereby ensuring the use of conductive PVC floor.

Conductive PVC floor is lighter in weight, more convenient to install, and the cost is relatively cheaper than tile anti-static floor and steel anti-static floor. It has been loved and sought after by consumers in our lives.

The destructiveness of static electricity in manufacturing has become a well-known situation, but it is not as easy to imagine that it is necessary to accurately control static electricity. Therefore, anti-static technology has played a relatively important role in the manufacturing industry.

Electrostatic dust removal uses the action of an electrostatic field to charge the dust particles suspended in the gas and to remove the dust particles from the flue gas. This is the primary aspect of electrostatic application and can be used for flue gas dedusting in various factories. The structure of the electrostatic precipitator is to insulate the rods or the filament-shaped high-voltage discharge electrodes from each other and hang them between the grounding plate dust collecting poles or the grounding cylinder. On the axis of the dust collecting pole, a negative high voltage is applied to the high voltage discharge electrode. When the voltage of the corona end is reached, a purple light spot appears on the surface of the high voltage pole, and a sound of dust or smoke is declared together. At the time of entry, particles such as dust and smoke are directly charged by the action of negative ions, and they are adsorbed on the dust collecting electrode by the electric field and piled up, and the purified gas is extracted therefrom. The accumulated dust falls off when it hits the dust collecting pole and is eradicated.
Compared with the general centrifugal method, cleaning, filtration and other dust removal methods, electrostatic dust removal has higher dust removal efficiency, generally up to 95%, and high up to 99%. It can capture particles larger than 0.01 micron, and the size of dust removal is large, and the dust can be dry or wet. The pressure loss of the equipment is small, generally 10-20 mm water column, the maintenance is simple, the cost is less, the corrosive gas or dust can be treated, and the high temperature exhaust treatment can be performed, generally up to 350℃, and the special plan can reach 500℃. With less power consumption and a large amount of processing gas, the thermal power plant with a generating capacity of 1 million kilowatts can handle millions of meters per hour. However, with regard to equipment with a small amount of gas, the initial cost is high; for various types of dust, it is necessary to adjust the dust removal conditions. When dealing with flammable gases, it is necessary to have an explosion-proof method.

The effective use of electrostatic technology must rely on the perfect combination of electrostatic technology and processing, which in turn depends on a correct and satisfactory understanding of electrostatic technology and related processing common sense. This time we will introduce you with the most detailed and complete ESD protection technology, including all the topics you need to know, from hard science to soft science, from planning to operation, from technology to processing to provide you with unprecedented learning opportunities.